Schneider Electric Altivar 58 VW3-A58101 Instrukcja Użytkownika Strona 92
- Strona / 112
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
ALTIVAR
58 Keypad Display VVDED397047US R8/01
Chapter 3 — Diagnostics and Troubleshooting 08/01
92
© 1998–2001 Schneider Electric All Rights Reserved
ERR 3
Serial link error due to incorrect value. If
the keypad display is remotely mounted,
electrical noise may be present.
Cycle power on the drive controller. If keypad display
is remotely mounted, verify the cable is properly
shielded. Ensure the cable is routed away from motor
leads. If the problem persists, replace the keypad
display with part number VW3A58101U. Reprogram
any parameters that are not at factory default settings.
ERR 4
Internal error in the keypad display
software. If the keypad display is
remotely mounted, electrical noise may
be present.
Cycle power on the drive controller. If the keypad
display is remotely mounted, verify the cable is
properly shielded. Ensure the cable is routed away
from motor leads. If the problem persists, replace the
keypad display with part number VW3A58101U.
Reprogram any parameters that are not at factory
default settings.
ERR 5
Serial link error. If the keypad display is
remotely mounted, electrical noise may
be present.
Cycle power on the drive controller. If the keypad
display is remotely mounted, verify the cable is
properly shielded. Ensure the cable is routed away
from motor leads. If the problem persists, replace the
keypad display with part number VW3A58101U.
Reprogram any parameters that are not at factory
default settings.
ERR 6
Internal error in the keypad display
hardware
Cycle power on thedrive controller. If the problem
persists, replace the keypad display with part number
VW3A58101U.
ERR 7
Serial link time out error, the keypad
display is not getting a response from
the drive controller. If the keypad display
is remotely mounted, electrical noise
may be present.
Cycle power on the drive controller. If keypad display
is remotely mounted, verify the cable is properly
shielded. Ensure the cable is routed away from motor
leads. If the problem persists, replace the control
board on the drive controller with part number
VX4A581U. An Ini fault may be displayed if the
problem persists.
ERR 8
ERR 9
Internal error in the keypad display
software. If the keypad display is
remotely mounted, electrical noise may
be present.
Cycle power on thedrive controller. If the keypad
display is remotely mounted, verify the cable is
properly shielded. Ensure the cable is routed away
from motor leads. Re-program any parameters that
are not at factory default settings. If the problem
persists, replace the keypad display with part number
VW3A58101U.
ERR10
Serial link error due to incorrect length of
frame. If the keypad display is remotely
mounted, electrical noise may be
present.
Cycle power on the drive controller. If the keypad
display is remotely mounted, verify the cable is
properly shielded. Ensure the cable is routed away
from motor leads. If the problem persists, replace the
keypad display with part number VW3A58101U. Re-
program any parameters that are not at factory default
settings.
Table 25: Fault Codes and Messages (Continued)
Fault/Message Probable Causes Corrective Actions
- 58 Adjustable Speed 1
- Drive Controllers 1
- Instruction Bulletin 1
- 08/01 Contents 3
- Contents 08/01 4
- CHAPTER 1—OVERVIEW 7
- (Continued) 10
- Chapter 1 — Overview 08/01 12
- 50 Hz 60 Hz 13
- 50/60 Hz switch 13
- VVDED397047US R8/01 ALTIVAR 15
- 08/01 Chapter 1 — Overview 15
- Figure 6: Menus 19
- CHAPTER 2—MENUS 21
- Validate? ENT/ESC 23
- CUS:Customize 24
- 08/01 Chapter 2 — Menus 25
- Handling Macro-Configuration 32
- Macro-Configuration 34
- Torque Macro-Configuration 35
- Reassignment (Continued) 37
- Chapter 2 — Menus 08/01 38
- T1 = 1/Acc 42
- T1 = 1/Dec 42
- drive controller to control 44
- 24 V LI1 LI2 LIx 45
- ATV58 Terminal strip 45
- LI1: Stop 45
- LI2: Forward 45
- LIx: Reverse 45
- ATV58 terminal strip 46
- 24 V LI1 LIx 46
- LI1: Forward 46
- AOL AOH 20 48
- Parameter 48
- LI1 LI2 LI3 LI4 +24 AIX 58
- Input Code Range Description 67
- T = non-adjustable delay 70
- Table 21: 6—Fault Menu 77
- Parameter Code Description 78
- Adjustment 78
- Factory 78
- Wiring OK? ENT/ESC 80
- Password Fault 82
- Red FAULT LED 85
- L1 L2 L3 PA PB U V W 89
- L1 L2 + – UVW 89
- FAULT CODES AND MESSAGES 91
- ItH, see 93
- ≥ 200 ms) 94
- Trip Point Reset Point 95
- Table 33: Menu 7—File Menu 100
- Menu 3 – DRIVE Menu (page 39) 101
- Menu 5– I/O Menu (page 51) 102
- Menu 6 – FAULT Menu (page 75) 102
- Menu 7 – FILES Menu (page 79) 102
- Continued on 103
- Catalog No. Description 104
- Description For Use on Drives 105
- Catalog 105
- 58 Keypad Display 107
- 08/01 Index 107
- Index 08/01 108
- Square D Company 112
- 8001 Hwy 64 East 112
- Knightdale, NC 27545 USA 112
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Schneider Electric Altivar 58 VW3-A58101
(40 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji